Stag/Stag Digest Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Electrical Puzzles - more
Sorry Glen, I didn't word this very well.
What I am asking is why is it 25 amp fuses for each 55 watt headlamp bulb, and
10 amp fuses for each 55 watt dip lamp bulb. They are the same bulbs GLB448.
They all have dedicated wire. Why the difference in fuses?
Peter H
In a message dated 26/10/1998 17:47:06 GMT, [email protected] writes:
<< Subj: Re: Electrical Puzzles - more
Date: 26/10/1998 17:47:06 GMT
From: [email protected] (Glenn Merrell)
To: [email protected]
CC: [email protected]
Hello Peter,
I would hope that the fusing in your fuse block is there to protect the wire
leading from the fuse block to the various accessories. That is the normal
function of a fuse. Wire current carrying capacity is sized to carry at
least
125% of the maximum current load of the device, and the fuse is (should be)
sized to protect the wire from drawing more current than it is designed to
carry
before it burns up and catches your car on fire. This 125% is a minimum
value
for safety. he wire may be larger. By adding a larger fuse, you risk
burning
up the wire harness.
The second reason that the fuse is more than four times the actual operating
load amps to the headlights is is different than the initial current surge
from
the lamps being switched on. First initial current to an inductive device
like
a lamp is like a shorted circuit for a millisecond or two. This initial
"inrush" of current is not enough to heat up the fuse to burn it out. In
other
words, the wire to the headlights should be sized to carry 125% more than the
rating of the fuse so the fuse breaks before burning up the wire, and the
fuse
is sized for the full maximum rating of the device.
Just some basic electrical standards stuff, not my opinion, and I would not
speculate buy adding more stuff on the circuits.
Regards,
Glenn Merrell
Triumph Stag Register USA VP
"Keep Your Stag Cool, Install a NEW Composite Cowl Today"
See it at the site below:
http://pw1.netcom.com/~gmerrel/stagcowl001.html
Support your Local and National Triumph Clubs
Vintage Triumph Register membership inquiry's:
http://www.vtr.org/brochure/membership-form.html
Triumph Stag Club, USA membership inquiry's to:
Bruce Krobusek, President
mailto:[email protected]
Triumph Stag Registry UK membership inquiry's to:
Mike Wattam, Chairman
mailto:[email protected]
[email protected] wrote:
>
> Hi all
> Puzzle 1
> Why is there a 25 Amp fuse for each headlamp and a 10 amp fuse for each dip
> lamp.
> In UK they are all the same bulbs, 55watt. divide 55 by 12 Volts = 4.58
Amps.
> Thus 10 amps should be enough for both main and dip.
> Puzzle 2
> On the cover of the fuse box we see Headlights Main Beam 1
> then Headlights Main Beam 2
> then Headlight Dip Beam RH
> Headlamp Dip Beam LH
> Why use a 1 and 2 convention in naming the main beams, and a RH LH
convention
> to name the dip beams?
>
> I have just wired in a rear Fog Lamp to my 1971 Car, hence my current (ha
ha)
> preoccupation with things electrical.
> I wired the fog lamp so that it comes on when I put the Master light Switch
to
> the FOG position. Trouble is the headlights go out because this switch
> position is meant for Front Fog lamps. However on the relay board I have
> installed an extra relay powered by the fog lamp wire and this pulls the
> headlamps back in by drawing power from the spare overdrive fuseway to the
> spare blade on the headlamp (Dip) fuseway.
> I think it is quite a good arrangement. I hope you do too!
> Peter H
----------------------- Headers --------------------------------
Return-Path: <[email protected]>
Received: from rly-zb04.mx.aol.com (rly-zb04.mail.aol.com [172.31.41.4]) by
air-zb04.mail.aol.com (v50.22) with SMTP; Mon, 26 Oct 1998 12:47:05 -0400
Received: from dfw-ix15.ix.netcom.com (dfw-ix15.ix.netcom.com
[206.214.98.15])
by rly-zb04.mx.aol.com (8.8.8/8.8.5/AOL-4.0.0)
with ESMTP id MAA18562 for <[email protected]>;
Mon, 26 Oct 1998 12:47:04 -0500 (EST)
Received: (from smap@localhost)
by dfw-ix15.ix.netcom.com (8.8.4/8.8.4)
id LAA05505; Mon, 26 Oct 1998 11:47:02 -0600 (CST)
Received: from den-co72-22.ix.netcom.com(206.214.152.150) by dfw-
ix15.ix.netcom.com via smap (V1.3)
id rma005440; Mon Oct 26 11:46:32 1998
Message-ID: <[email protected]>
Date: Mon, 26 Oct 1998 10:46:11 -0700
From: Glenn Merrell <[email protected]>
Organization: Freelance Consulting <http://www.netcom.com/~gmerrel/
X-Mailer: Mozilla 4.07 [en] (Win98; I)
MIME-Version: 1.0
To: [email protected]
CC: [email protected]
Subject: Re: Electrical Puzzles - more
References: <[email protected]>
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
>>
Home |
Archive |
Main Index |
Thread Index